Does your printer have frequent paper jams? Does it put ink where ink shouldn't be? Is the outside of your printer dirty or covered with smudges? If so, it is time to clean your printer.
First, there are some general rules that apply to cleaning just about any electrical device. It is best to turn off the printer before cleaning it. Do not spray water or cleaner on or in the printer. Instead wet the rag with it and clean the printer with the rag.
Different types of printers require different cleaning methods. So if you can get your hands on cleaning instructions for your make and model of printer, do so and follow them. Unfortunately, many manufacturers only make that kind of information available to their licensed technicians. In that case, you are stuck with these instructions, so read on.
Open up your printer and take a look.
If you have an ink jet printer and there is an ink mess inside, clean it up with wet paper towels.
If you have a printer that uses toner either vacuum or blow it out. Some toner, especially color toner, can be harmful to you, so only use a vacuum with a micro-toner filter or blow and run. Figure out where the drum is (it is shiny and larger in diameter than the rollers) and do not touch or scratch it. If you do, the scratches will turn up as marks on every paper that you print and will require that you replace the drum (not a cheap option) to fix it.
Examine the path that the paper takes through the printer. Clean all of the rollers (but on a toner printer, not the drum or rollers near the drum and watch out for the rollers after the drum because they may be hot). It may take some disassembly and/or contorting of your arm to get to some of the rollers. Access is not always easy. The most important rollers to clean are the ones which pick up the paper from the paper bin and transfer it into the printer. If these rollers are dirty or bad, they will cause consistent paper jams.
The rollers are made of either hard plastic or rubber. All of the rollers can be cleaned with water or rubbing alcohol. If the rubber rollers have deposits that you can't get off, you can use harsher cleaners but be careful because those cleaners can damage the plastic rollers and parts.
To clean a roller, wipe across the roller with a wet rag, rotate the roller, and wipe again. Do this until you have worked your way all the way around the roller. Look at the rag. If it has been blackened by the roller, move to a clean part of the rag and clean the roller again.
Once everything is clean on the inside, close it up and clean the outside. Wipe off the case and each of the buttons or knobs. If there are staples or paper clips sitting on it or wedged in the cracks, remove them and throw them away.
Other areas of the printer can be cleaned but to do so, you will have to either get training and special tools or leave it to a trained professional.
Read More ..
Custom Search
Showing posts with label tips. Show all posts
Showing posts with label tips. Show all posts
2/28/2009
Clean your Mouse
If your mouse is working sluggishly or not at all, don't go out and buy another cheap mouse. The cause is probably just a dirty mouse. A quick cleaning could fix the problem.
First, you need to identify which kind of mouse you have. If you turn your mouse over and part of a ball is showing, you have a ball mouse. If you see a lens, you have an optical or laser mouse. Each type of mouse requires a different type of cleaning.
The optical or laser mouse does not need to be cleaned near as often as the ball mouse, but it and the surface it runs on can still get dirty. If you do not clean the surface that the mouse moves on, it will soon turn black. So about once a month or so, wipe the surface off with a wet rag. The lens probably never will get dirty, but if it does, take a soft cloth, cotton swab, or q-tip wetted with window cleaner or alcohol and clean the lens.
The ball mouse may need cleaning quite often, so you should get well acquainted with the following cleaning procedure. The dirtier the ball mouse gets, the harder it is to get it to move the cursor on the screen smoothly. If you have to move the mouse across the mouse pad several times to get the cursor to move halfway across the screen, it needs to be cleaned.
The mouse does not need to be disconnected to clean it, but you should close all of the programs that are running, so that you don't accidentally click on something and mess it up. If you do decide to disconnect the mouse, be sure to turn off the computer first. The mouse cord should never be unplugged from the computer while it is running. Doing so could ruin your motherboard.
Turn the ball mouse over and find the cover that holds the ball in. Look for arrows on the cover to show which way it needs to be turned. Place two fingers on the cover and push in the direction of the arrows. Once the cover has been turned about an inch, cover it with your hand and turn the mouse back over to the upright position. The ball and cover should fall into your hand. If it doesn't, shake the mouse gently.
Wipe the ball off with a wet rag.
Now look in the ball well and find the three rollers. Start by cutting across the buildup on the rollers with your fingernail (a knife or steel dental pick may also be used gently), then turn the roller and remove the buildup as you go along. If you do this correctly, you will end up with one curled strip of buildup for each roller. Make sure to remove the buildup from the well. If it falls inside somewhere, blow and gently shake it until it comes out.
Take a wet rag and clean each of the rollers by wiping across it, then turning it and wiping again. Continue until the entire roller is cleaned. Put the ball back in the ball well and lock the cover back in place.
If the mouse still has problems once it is assembled, try cleaning it again. If that doesn't work, you may need to buy a new mouse.
It is a good idea to regularly clean the surface that the mouse is on because the cleaner the surface, the less dirt will get inside the mouse and the less often you will have to clean it.
If your mouse is shared by many people (especially if one of them is sick), you may want to disinfect the top of the mouse between users.
Follow these instructions and your mouse will be up and darting again in no time.
Read More ..
First, you need to identify which kind of mouse you have. If you turn your mouse over and part of a ball is showing, you have a ball mouse. If you see a lens, you have an optical or laser mouse. Each type of mouse requires a different type of cleaning.
The optical or laser mouse does not need to be cleaned near as often as the ball mouse, but it and the surface it runs on can still get dirty. If you do not clean the surface that the mouse moves on, it will soon turn black. So about once a month or so, wipe the surface off with a wet rag. The lens probably never will get dirty, but if it does, take a soft cloth, cotton swab, or q-tip wetted with window cleaner or alcohol and clean the lens.
The ball mouse may need cleaning quite often, so you should get well acquainted with the following cleaning procedure. The dirtier the ball mouse gets, the harder it is to get it to move the cursor on the screen smoothly. If you have to move the mouse across the mouse pad several times to get the cursor to move halfway across the screen, it needs to be cleaned.
The mouse does not need to be disconnected to clean it, but you should close all of the programs that are running, so that you don't accidentally click on something and mess it up. If you do decide to disconnect the mouse, be sure to turn off the computer first. The mouse cord should never be unplugged from the computer while it is running. Doing so could ruin your motherboard.
Turn the ball mouse over and find the cover that holds the ball in. Look for arrows on the cover to show which way it needs to be turned. Place two fingers on the cover and push in the direction of the arrows. Once the cover has been turned about an inch, cover it with your hand and turn the mouse back over to the upright position. The ball and cover should fall into your hand. If it doesn't, shake the mouse gently.
Wipe the ball off with a wet rag.
Now look in the ball well and find the three rollers. Start by cutting across the buildup on the rollers with your fingernail (a knife or steel dental pick may also be used gently), then turn the roller and remove the buildup as you go along. If you do this correctly, you will end up with one curled strip of buildup for each roller. Make sure to remove the buildup from the well. If it falls inside somewhere, blow and gently shake it until it comes out.
Take a wet rag and clean each of the rollers by wiping across it, then turning it and wiping again. Continue until the entire roller is cleaned. Put the ball back in the ball well and lock the cover back in place.
If the mouse still has problems once it is assembled, try cleaning it again. If that doesn't work, you may need to buy a new mouse.
It is a good idea to regularly clean the surface that the mouse is on because the cleaner the surface, the less dirt will get inside the mouse and the less often you will have to clean it.
If your mouse is shared by many people (especially if one of them is sick), you may want to disinfect the top of the mouse between users.
Follow these instructions and your mouse will be up and darting again in no time.
Read More ..
How to clean your Mother Board
If you have not done the inspection mentioned in the previous article - How to Clean your Case, now is the time to do so. Look at the blades of the fan in the back of the computer. Also look at any vents. Is there clusters of dust there? Is there grime caked on to it? If so, the inside needs to be cleaned. If the fan blades are clean but it has been several years since you have cleaned the motherboard or if the computer is around cigarette smoke, it probably should be cleaned anyway. Dust and particles in the air (like cigarette smoke) can build up on the circuitry of the motherboard and cause it to heat up and/or corrode.
The first thing that you need to do is unplug your computer. Then open up the case to get access to the motherboard. Cases open differently. If you don't know how to open your case, look on the back of your computer along the edge for some screws. These screws may hold on side panels or an upside down U shaped panel that covers the sides and top. Removing the screws will allow you to take off the cover. Other cases have the screws on the front of the computer. To get access to these screws, you must first remove the front panel by pressing a hidden latch. The cover is there to give easy access to the inside of your computer, so if you look hard enough, you should be able to figure out how to remove it.
Remember that if you touch anything on the motherboard, you should be grounded by either touching the metal frame of the computer with your other hand or by wearing a special grounding device.
The goal of cleaning the motherboard is to remove all dust and debris from the motherboard and all components inside of the case. This can be done using one of three methods.
The preferred method is to use a can of compressed air to blow it out. Always hold the can in an up-right position to prevent the propellent chemicals which can damage or corrode components from coming out. Dust and dirt should be blown away from the motherboard and out of the case.
Another way to remove dust is to use a vacuum. The common advice is to only use a battery operated vacuum because an AC powered vacuum causes static and static can ruin the motherboard. I have used an AC powered vacuum (before I knew that it was not recommended) to clean my motherboard many times and it has never caused any problems, but I may have just been lucky. When using the vacuum, keep the nozzle a couple of inches away from the motherboard or any other components so that it does not come in contact with them and so that any small parts are not sucked into the vacuum.
If you do not have a can of compressed air or a vacuum, you can use a dry cloth and brush to clean the motherboard. Be careful not to dislodge or break anything using this method.
While cleaning the motherboard, be careful not to unplug any cables or connections or to dislodge any loose components, such as, jumpers.
Methodically clean the whole inside of the case going over all of the motherboard from one end to the other and all other components. Don't forget to clean the fans and heat sinks. Do not open up the power supply box or stick anything in it beyond the fan. If you do, you could get a shocking surprise and ruin your computer.
If your computer does not work when you put it back together, something was obviously dislodged during the cleaning. Open the case back up and push all connections and cards into their slots. Look for anything that may have become disconnected.
Cleaning the motherboard is probably the most dangerous form of cleaning but it is necessary to prevent an early death of your computer.
Read More ..
The first thing that you need to do is unplug your computer. Then open up the case to get access to the motherboard. Cases open differently. If you don't know how to open your case, look on the back of your computer along the edge for some screws. These screws may hold on side panels or an upside down U shaped panel that covers the sides and top. Removing the screws will allow you to take off the cover. Other cases have the screws on the front of the computer. To get access to these screws, you must first remove the front panel by pressing a hidden latch. The cover is there to give easy access to the inside of your computer, so if you look hard enough, you should be able to figure out how to remove it.
Remember that if you touch anything on the motherboard, you should be grounded by either touching the metal frame of the computer with your other hand or by wearing a special grounding device.
The goal of cleaning the motherboard is to remove all dust and debris from the motherboard and all components inside of the case. This can be done using one of three methods.
The preferred method is to use a can of compressed air to blow it out. Always hold the can in an up-right position to prevent the propellent chemicals which can damage or corrode components from coming out. Dust and dirt should be blown away from the motherboard and out of the case.
Another way to remove dust is to use a vacuum. The common advice is to only use a battery operated vacuum because an AC powered vacuum causes static and static can ruin the motherboard. I have used an AC powered vacuum (before I knew that it was not recommended) to clean my motherboard many times and it has never caused any problems, but I may have just been lucky. When using the vacuum, keep the nozzle a couple of inches away from the motherboard or any other components so that it does not come in contact with them and so that any small parts are not sucked into the vacuum.
If you do not have a can of compressed air or a vacuum, you can use a dry cloth and brush to clean the motherboard. Be careful not to dislodge or break anything using this method.
While cleaning the motherboard, be careful not to unplug any cables or connections or to dislodge any loose components, such as, jumpers.
Methodically clean the whole inside of the case going over all of the motherboard from one end to the other and all other components. Don't forget to clean the fans and heat sinks. Do not open up the power supply box or stick anything in it beyond the fan. If you do, you could get a shocking surprise and ruin your computer.
If your computer does not work when you put it back together, something was obviously dislodged during the cleaning. Open the case back up and push all connections and cards into their slots. Look for anything that may have become disconnected.
Cleaning the motherboard is probably the most dangerous form of cleaning but it is necessary to prevent an early death of your computer.
Read More ..
How To clean your Case
There is nothing wrong with leaving spills, dirt, and stains on your computer case. After all isn't that what the case is for, to protect the electronic components inside from spills and dirt? This is true, but there are still parts of the case that need to be cleaned and checked if you want your computer to live a long and prosperous life.
Unless you like looking at dirt everytime you look at your computer, you should go ahead and clean those spills, stains, and dust off of the case. You can do this with just about any cloth and cleaner. Do not use highly abrasive cleaners that might ruin or mar the surface and do not use solvents on plastic. A wet sponge will even work. Just make sure that the cleaner or any liquid does not seep into the inside through cracks and vents. If there is any possibility that you are going to get that messy, turn off and unplug the computer first and wait to turn it back on until any liquid has had a chance to fully dry
After you have wiped off the outside, it is time for a little inspection. Look at the blades of the fan in the back of the computer. Also look at any vents. Is there dust there? Is there a lot of dust and grime caked on to it? If so, that is an indicator that the inside also needs to be cleaned (I will tell you how to do that in next week's article - How to Clean your Motherboard).
Some clean environments never have to have the inside cleaned. Some need it cleaned monthly. When I lived in Russia, even though I didn't notice it, the air was not clean. The fan on the computer would cake up with dirt and grime after about a month of use. And so I would have to clean the fan, vents, and inside monthly. If I had let it go for several months without cleaning, the fan would have stopped working and the computer would have overheated. Where I now live in the US, the air is clean and I have gone years without having to clean it. Again, the indicator of this is the blades of the fan and the vents. If they are dirty, they need to be cleaned.
You can do some of the cleaning from the outside. First, turn off the computer. Then get out the vacuum sweeper and using the hose, vacuum out the vents and the fan(s). If you have compressed air (you can purchase compressed air from your computer store), you may want to blow air in through the vents (or intake fan if you have one) to loosen the dust and suck it out using the vacuum. If there is still dust or dirt in the vents or on the blades of the fan, you can use a Q-tip to clean them.
If you do not have a vaccum, you can use compressed air alone. Always use short bursts to avoid moisture buildup. Start with the computer off and blow into every hole and vent. Then turn the computer on and blow everything except for the exhaust fan once again.
With the case clean, your computer will look nicer and with the fan and vents cleaned out it will breathe easier and run cooler.
Read More ..
Unless you like looking at dirt everytime you look at your computer, you should go ahead and clean those spills, stains, and dust off of the case. You can do this with just about any cloth and cleaner. Do not use highly abrasive cleaners that might ruin or mar the surface and do not use solvents on plastic. A wet sponge will even work. Just make sure that the cleaner or any liquid does not seep into the inside through cracks and vents. If there is any possibility that you are going to get that messy, turn off and unplug the computer first and wait to turn it back on until any liquid has had a chance to fully dry
After you have wiped off the outside, it is time for a little inspection. Look at the blades of the fan in the back of the computer. Also look at any vents. Is there dust there? Is there a lot of dust and grime caked on to it? If so, that is an indicator that the inside also needs to be cleaned (I will tell you how to do that in next week's article - How to Clean your Motherboard).
Some clean environments never have to have the inside cleaned. Some need it cleaned monthly. When I lived in Russia, even though I didn't notice it, the air was not clean. The fan on the computer would cake up with dirt and grime after about a month of use. And so I would have to clean the fan, vents, and inside monthly. If I had let it go for several months without cleaning, the fan would have stopped working and the computer would have overheated. Where I now live in the US, the air is clean and I have gone years without having to clean it. Again, the indicator of this is the blades of the fan and the vents. If they are dirty, they need to be cleaned.
You can do some of the cleaning from the outside. First, turn off the computer. Then get out the vacuum sweeper and using the hose, vacuum out the vents and the fan(s). If you have compressed air (you can purchase compressed air from your computer store), you may want to blow air in through the vents (or intake fan if you have one) to loosen the dust and suck it out using the vacuum. If there is still dust or dirt in the vents or on the blades of the fan, you can use a Q-tip to clean them.
If you do not have a vaccum, you can use compressed air alone. Always use short bursts to avoid moisture buildup. Start with the computer off and blow into every hole and vent. Then turn the computer on and blow everything except for the exhaust fan once again.
With the case clean, your computer will look nicer and with the fan and vents cleaned out it will breathe easier and run cooler.
Read More ..
How to Clean Disc Drives
When your CD or DVD (disc) drive starts giving you problems, your first thought may be to replace it or take it to the repair shop, but a good cleaning may be all it needs.
Below are three methods to clean the disc drive. The easiest method is the least effective. The hardest method is the most effective. Since the hardest method takes some time to do, I recommend that you start with the easiest method. If it solves your problems, congratulations. If not, try the next method.
The Cleaner Disc method - this, the easiest method, uses a special cleaner disc which can be purchased in computer stores. The disc usually comes with a little bottle of cleaner solution. Apply a few drops of the solution to the disc and insert it in the disc drawer (be sure to read and follow the instructions that come with the cleaner disc). The drive will turn the disc and clean the lens. Unfortunately, this only works adequately about half the time.
The Cleaning Stick method - this is what I do in desperation when the cleaner disc does not work and I don't want to disassemble the drive. Since all that is needed (at least in my mind this is true) is a little more pressure applied to the lens, I start out in search of a thin, flexible stick of some type which is at least six inches long. It should not have sharp or rough edges that would scratch the lens. Next, get a soft, thin cloth and put water or rubbing alcohol in the middle of it. Place one end of the stick under the wet part of the cloth and slide it into the opened disc drawer. The goal is to rub the wet cloth on the lens to clean it. Do not apply so much pressure that you will scratch and ruin the lens. Also try blowing into the disc drive to remove any dirt that may have accommulated in it. If you do not succeed at this, proceed to the next method.
The Disassembly method - this method should work but it requires you to disassemble the drive. So if you are not comfortable with taking the drive apart, please take it to a computer repair shop and let them do it.
Take the cover off your computer, unplug the cords from the back of the disc drive, remove any screws holding it in, and slide it out (you may need to remove the face plate on the end of the drawer to get the drive out). Remove the screws in the drive housing and take the cover off. The bottom side of the drive is a circuit board, so if that is what you see when you take the cover off, figure out how to access the other side. On the correct side, you should see a lens that runs on a track (there is no harm in moving the lens along the track but do not touch the lens itself). Use a wet, soft cloth to clean the lens.
Sometimes a disc drive malfunctions because there is too much dust or debris in it, so be sure to clean out the inside with either compressed air, a soft cloth, or a cotton swab. Reassemble the disc drive, put it back in the computer case, and cross your fingers. Hopefully, it will work when you turn on the computer.
If these methods work, you just saved yourself some money. If not, you needed a better disc drive anyway.
Read More ..
Below are three methods to clean the disc drive. The easiest method is the least effective. The hardest method is the most effective. Since the hardest method takes some time to do, I recommend that you start with the easiest method. If it solves your problems, congratulations. If not, try the next method.
The Cleaner Disc method - this, the easiest method, uses a special cleaner disc which can be purchased in computer stores. The disc usually comes with a little bottle of cleaner solution. Apply a few drops of the solution to the disc and insert it in the disc drawer (be sure to read and follow the instructions that come with the cleaner disc). The drive will turn the disc and clean the lens. Unfortunately, this only works adequately about half the time.
The Cleaning Stick method - this is what I do in desperation when the cleaner disc does not work and I don't want to disassemble the drive. Since all that is needed (at least in my mind this is true) is a little more pressure applied to the lens, I start out in search of a thin, flexible stick of some type which is at least six inches long. It should not have sharp or rough edges that would scratch the lens. Next, get a soft, thin cloth and put water or rubbing alcohol in the middle of it. Place one end of the stick under the wet part of the cloth and slide it into the opened disc drawer. The goal is to rub the wet cloth on the lens to clean it. Do not apply so much pressure that you will scratch and ruin the lens. Also try blowing into the disc drive to remove any dirt that may have accommulated in it. If you do not succeed at this, proceed to the next method.
The Disassembly method - this method should work but it requires you to disassemble the drive. So if you are not comfortable with taking the drive apart, please take it to a computer repair shop and let them do it.
Take the cover off your computer, unplug the cords from the back of the disc drive, remove any screws holding it in, and slide it out (you may need to remove the face plate on the end of the drawer to get the drive out). Remove the screws in the drive housing and take the cover off. The bottom side of the drive is a circuit board, so if that is what you see when you take the cover off, figure out how to access the other side. On the correct side, you should see a lens that runs on a track (there is no harm in moving the lens along the track but do not touch the lens itself). Use a wet, soft cloth to clean the lens.
Sometimes a disc drive malfunctions because there is too much dust or debris in it, so be sure to clean out the inside with either compressed air, a soft cloth, or a cotton swab. Reassemble the disc drive, put it back in the computer case, and cross your fingers. Hopefully, it will work when you turn on the computer.
If these methods work, you just saved yourself some money. If not, you needed a better disc drive anyway.
Read More ..
2/25/2009
10 Helpful Tips For Running A Profitable Web Site
1. Address your targeted audience on your business site. Example: "Welcome Internet Marketers". If you have more than one, address them all.
2. Make sure your content and graphics are relevant to your web site's theme. You wouldn't want to use a bird graphic on a business web site.
3. Alert visitors by email when you add new content to your web site. This will remind people to revisit your web site.
4. Offer a way for visitors to contact you on each web page. List your email address, fax number and phone number.
5. Give people the option of viewing your web site offline. Offer it by autoresponder or printer friendly version.
6. Make sure a least 50f your content is original. The other option is to offer something else original other than content, like software or an online utility.
7. Offer your visitors incentives for revisiting your web site. You could give them new content, ebooks, software, ezine, etc.
8. Publish a FAQs for your business, product and web site. They could have questions about multiple parts of your business.
9. Make sure all links on the navigational bar are clickable. If people can't get to where they want to go, they will leave.
10. Organize you web site in logical and profitable sequence. You don't want to give a freebie before they learn about the product(s) you're selling. Read More ..
Subscribe to:
Posts (Atom)
